RDL®

ST-VP2

Automatic Ducking Module

SKU: ST-VP2
  • Fully AUTOMATIC Voice-Over Mixing
  • Noiseless Paging
  • Adjustable Fade Depth
  • Setting to Fade Music Fully Off
  • Adjustable Recovery Rate
  • Built-in AGC Compressor on Music Input
  • Recommended Power Supply ( Not Included )
    PS-24AS (USA)PS-24AX (International)

    Description

    The ST-VP2 can be wired into any line-level input of a paging amplifier. A line-level music source may be provided from a receiver, satellite decoder, tape or CD source. A line-level voice source may be provided from a telephone paging system at line level, or from a microphone which has been preamplified up to line level (See RDL STM-1, STM-2, STM-2X, STM-3, STM-LDA3 Microphone Preamplifiers). When a page is initiated, the module automatically senses the audio at the input, turns the music down to the desired level, and automatically fades the music back up after the page is completed. The VOICE input is completely turned off by the module until the next paging signal is received. Setup is made easy by two LED indicators at the front of the module. LEDs are provided to show correct operating level for each of the two inputs.

    The music input provides an AGC/Compressor which transparently produces a consistent audio level for varying music sources and protects against excessive music levels which would otherwise mask the voice signal during voice-overs.

    Specifications

    Inputs (2):Balanced line level (or unbalanced)
    Input Impedance:20 kΩ
    Input Signal Range:-20 dBu to +18 dBu
    Output:+4 dBu balanced (nominal)
    Gain:Adjustable using multiturn potentiometer
    THD+N:< 0.01% (20 Hz to 20 kHz, no compression)
    Frequency Response:20 Hz to 20 kHz (± 1 dB)
    Noise:< -70 dB
    Indicators (2):1 LED indicating proper music level 1 LED indicating proper voice level
    AGC/Compressor:18 dB range; 6 dB compression at normal input level
    Attack Time:25 ms
    Release Time:2.5 seconds
    Voice Trigger Level:24 dB below operating level
    Music Fade Depth:Adjustable 0 dB to −25 dB, or off
    Music Recovery Delay:Adjustable 2 seconds to 4 seconds
    Ambient Operating Environment:0° C to 55° C
    Power Requirement:GROUND-REFERENCED, 24 Vdc @ 35 mA
    Package Type:Cardboard Box
    Package Dimensions:2 x 2 x 4 in.
    Shipping Weight:0.2 lbs.
    WEEE weight:0.145 lbs.
    Tariff code:8543.70.9860

    Related Products

    Annunciation & Paging
    • ST-VP1

      Voice-Over / Paging Module - Manual

    Related Products

    DIN Rail Mounting Accessories
    • DRA-35S

      STICK-ON DIN Rail Adapter - 1 module

    • DRA-35S6

      STICK-ON DIN Rail Adapter - 6 modules

    General Mounting Accessories
    • DMK-5

      Detachable Mounting Kit for RDL Modules

    • SR-4

      STICK-ON Series Mounting Rack - 7 modules

    • MB-1

      Mounting Kit - RU, ST and TX Series

    TX™ Mounting Accessories
    • MB-1

      Mounting Kit - RU, ST and TX Series

    General Wiring Accessories
    • DTB

      STICK-ON® Series Detachable Terminal Block

    STICK-ON® Mounting Accessories
    • STR-H6A

      10.4" Rack Mount for 6 STICK-ON Series Products

    • ST-PBR4

      STICK-ON Mounting Bracket

    • ST-RRB1

      Rear rack rail mounting kit for any STICK-ON module

    • SMK-12

      STICK-ON Mounting Plate

    • STR-19A

      STICK-ON Series 19" Racking System - 12 modules

    • SR-12A

      STICK-ON Series 19" Mounting Rack - 12 modules

    • STR-19B

      STICK-ON Series 19" Racking System - 10 modules

    • SR-10

      STICK-ON Series 19" Mounting Rack - 10 modules

    Dimensions

    ST-VP2

    Downloads

    DocumentsFormat
    DatasheetPDF
    CAD FilesUnitsSizeFormat
    Engineering Functional BlockAmerican3.92 KBDXF
    Panel Diagram - EndAmerican11.85 KBDXF
    Panel Diagram - FrontAmerican24.77 KBDXF
    Panel Diagram - EndMetric12.06 KBDXF
    Panel Diagram - FrontMetric25.61 KBDXF
    High Res ImagesFormat
    st-vp2.zipTIF
    Declaration of Conformity
    Download

    Diagrams

    How To Buy

    Direct Dealer Program

    Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

    • Must be an A/V contractor, sound contractor or system integrator
    • Must possess a current resale certificate for your state
    Click here to submit a new direct dealer account inquiry

    Buy Online

    CompanyAddressPhoneLink
    Shopping cart close