RDL®

RU-MLA2T

Dual Microphone / Line Preamplifier

SKU: RU-MLA2T
  • Two-channel Audio Preamplifier
  • Front Panel XLR Input / Output Jacks
  • Detachable Input / Output Terminal Blocks
  • Switch-selectable Mic or Line Inputs
  • Switch-selectable Mic Gain and Phantom
  • Gain Trim on Each Input
  • Each Output Switch-selectable Mic or Line
  • Recommended Power Supply ( Not Included )
    PS-24AS (USA)PS-24AX (International)

    Description

    The RU-MLA2 is a dual channel audio preamplifier. The inputs and outputs may be connected through the front-panel XLR jacks or on the rear panel detachable terminal blocks. Each input accepts either a balanced microphone or line level signal. Each output provides either a microphone or line level signal. Both the front-panel XLR connectors and the rear-panel terminals are active at all times. The RU-MLA2 may be rack-mounted with the XLR jacks facing forward, or may be reverse-mounted using the RDL RU-FP1 Filler Panel/Reverse Mount Kit.

    Each audio input is equipped with a rear-panel switch to select between MIC and LINE level. Two additional switches on each input allow setting the MIC input for LO or HI gain and for enabling or disabling standard 24 Vdc phantom. The two microphone gain settings allow the connection of a wide variety of dynamic and condenser microphones. Each output is provided with a separate rear-panel switch to set the associated level to either MIC or LINE. Audio outputs may be wired balanced or unbalanced. Crosstalk between channels is below the noise floor, allowing the RU-MLA2 to be operated as a stereo preamplifier or as two separate mono preamplifiers.

    Gain trim for each channel is provided on a front-panel control. An RDL Dual-led VU meter is provided above each channel gain trimmer. The meters are calibrated to indicate +4 dBu for outputs set to line level.

    The rear panel provides a detachable terminal block and a power input jack to connect 24 Vdc power. The RU-MLA2 audio outputs are active balanced. Each output of the RU-MLA2T is equipped with a studio-quality audio output transformer.

    Specifications

    Inputs (2):XLR(front); detachable term block(rear)
    Input level (for +4 dBu output):Switch-selectable (rear panel) MIC/LINE
      Mic:-48 dBu to -3 dBu (LO GAIN); -65 dBu to -20 dBu (HI GAIN)
      Line:-15 dBu to +28 dBu

    Input Impedance:
      Mic:2 kΩ balanced, switchable 24 V phantom (IEC 61938: 2013)
      Line:> 10 kΩ balanced; may be connected unbalanced
    Outputs (2):XLR(front); detachable term block(rear)
    Output Impedance:150 Ω balanced
    Channels:2 (A and B; stereo or dual mono)
    Gain Trim (2):Front panel adjustable; one per channel
      Mic:Off to 52 dB gain (LO GAIN); Off to 69 dB gain (HI GAIN)
      Line:Off to 20 dB gain

    Frequency Response:
    Mic80 Hz to 50 kHz (± 0.75 dB); < 10 dB @ 20 Hz (integral high-pass filter)
      Line:15 Hz to 50 kHz (± 0.1 dB)
    THD+N:< 0.1% (Mic); 60 dB (Mic); > 50 dB (Line)

    Residual Noise (below +4 dBu LINE output or -45 dBu MIC output):
      Mic:-79 dB (50 dB Gain); -70 dB (Mic 60 dB Gain)
      Line:-85 dB
    Headroom:> 20 dB (above +4 dBu LINE output)
    Ambient Operating Environment:0° C to 55° C
    Power Requirement:GROUND-REFERENCED, 24 Vdc @ 80 mA
    Package Type:Cardboard Box
    Package Dimensions:6 x 6 x 2.625 in.
    Shipping Weight:1.93 lbs.
    WEEE weight:1.695 lbs.
    Tariff code:8543.70.9860

    Related Products

    Microphone Products
    • FP-MP1

      Studio Quality Microphone Preamplifier with Phantom - Terminal block & XLR

    • HR-MP2

      Dual Microphone Preamplifier

    • HR-MP2A

      Dual Microphone Preamplifier

    • STM-1

      Microphone Preamplifier - 50 dB Gain

    • STM-2

      Adjustable Gain Microphone Preamplifier - 35 to 65 dB gain

    • STM-3

      High Gain Microphone Preamplifier - 45 to 75 dB gain

    Line Amplifiers / Interface
    • STA-1

      Dual Balanced/Unbalanced Line Amplifier -12 to 20 dB Gain

    • STA-2A

      Dual High Gain Line Amplifiers

    Related Products

    DIN Rail Mounting Accessories
    Rack-Up® Mounting Accessories
    • UC-2R

      Double Wide RACK-UP Enclosure

    • WDG1R

      Table Top "Wedge" Chassis

    • UC-1R

      RACK-UP Enclosure

    • RU-RA3R

      Rack adapter for RACK-UP series

    • RU-HRA1

      10.4" Rack Mount for 1 RACK-UP Series Product

    • RU-SMA1

      RACK-UP Mounting Plate - Mounts any RACK-UP module in a cabinet or other flat surface

    • RU-BR1

      Mounting Bracket for RACK-UP Series

    General Wiring Accessories
    • RC-1UR

      19" Universal Rack Chassis

    Dimensions

    RU-MLA2T

    Downloads

    DocumentsFormat
    DatasheetPDF
    CAD FilesUnitsSizeFormat
    Engineering Functional BlockAmerican4.06 KBDXF
    Panel Diagram - RearAmerican12.58 KBDXF
    Panel Diagram - FrontAmerican7.56 KBDXF
    Panel Diagram - RearMetric13.17 KBDXF
    Panel Diagram - FrontMetric7.62 KBDXF
    High Res ImagesFormat
    ru-mla2t.zipTIF
    Declaration of Conformity
    Download

    How To Buy

    Direct Dealer Program

    Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

    • Must be an A/V contractor, sound contractor or system integrator
    • Must possess a current resale certificate for your state
    Click here to submit a new direct dealer account inquiry

    Buy Online

    CompanyAddressPhoneLink
    Shopping cart close