RDL®

EZ-MPA1

Microphone Preamplifier - Stereo Output with Compressors

SKU: EZ-MPA1
  • Balanced Microphone Input on Rear-Panel XLR
  • Switch-Selectable Phantom on Rear Panel
  • Unbalanced Output on MINI or RCA Rear-Panel Jacks
  • Preamp Feeds Left and Right Output Channels
  • Front-Panel Compressor Enable/Disable Switch
  • Audio Compressor Controls Overloads
  • Front-Panel LEVEL Control
  • Dual-LED VU Meter
  • Optimized for Dynamic or Condenser Mics
  • Headroom Accomodates High Input Levels
  • Headroom Increases with Lower Gain Settings
  • Compressor Limits Clipping Over Wide Dynamic Range
  • Recommended Power Supply ( Included )
    PS-24AS (USA)PS-24AX (International)

    Description

    The EZ-MPA1 is a microphone preamplifier with front-panel volume control and audio level metering. A front-panel switch engages an audio compressor to control overloads and clipping during high level audio bursts or peaks from the microphone. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The preamplified mic signal feeds both channels of the line output on RCA or mini-jacks. LED VU metering facilitates easy level adjustment. The EZ-MPA1 is ideal to add microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems.

    Specifications

    Input:1.2 kΩ balanced on XLR jack, mic-level, -11 dBu max.
    Level control:Off to 50 dB gain
    Outputs (2):-10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
    Frequency Response:80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
    THD+N:< 0.1% (35 Hz to 20 kHz, -50 dBu input)
    Compression :20 dB range, switch-selectable
    CMRR:> 55 dB (20 to 20 kHz)
    Metering:Dual-LED VU Meter, calibrated to -10 dBV output
    Phantom:Switch-selectable 24 V (IEC 61938: 2013)
    Noise:< -65 dB (below -10 dBV output, -50 dBu input)
    24 Vdc power supply current:55 mA (idle), 80 mA (max.), 100 mA (max. with phantom)
    Case dimensions:5.75” (14.6 cm)W x 3” (7.6 cm)D
    Mounting size:1/3 rack width
    Package Type:Cardboard Box
    Tariff code:8543.70.9860
    WEEE weight:0.56 lbs.
    Shipping Weight:0.955 lbs.
    Package Dimensions:9.5 x 7 x 2.25 in.

    Related Products

    Microphone Products
    • EZ-MCP1

      Microphone Compressor

    • EZ-MPA2

      Dual Microphone Preamplifier - Stereo Output with Compressors

    • FP-MP1

      Studio Quality Microphone Preamplifier with Phantom - Terminal block & XLR

    • FP-MPA2

      Dual Microphone Phantom Adapter 12, 24, 48 V - XLR

    • HR-MP2

      Dual Microphone Preamplifier

    • HR-MP2A

      Dual Microphone Preamplifier

    • ST-MPA48

      Dual Microphone Phantom Adapter - 48 V

    • A compact high quality microphone preamplifier

      STM-1

      Microphone Preamplifier - 50 dB Gain

    • Microphone Preamplifier

      STM-2

      Adjustable Gain Microphone Preamplifier - 35 to 65 dB Gain

    • STM-2X

      Switched Microphone Preamplifier - 35 to 65 dB Gain

    • STM-3

      High Gain Microphone Preamplifier - 45 to 75 dB Gain

    • STM-LDA3

      Studio Quality Microphone Preamplifier with phantom - 3 line outputs

    Related Products

    EZ Mounting Accessories
    • EZ-CC6

      Component Chassis for 6 Increments of 1/6 Rack Width

    • EZ-DC2

      Desktop Chassis for 1/3 Rack Width EZ Products

    • EZ-FP1

      Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6

    • EZ-RA6

      Rack Adapter for 6 Increments of 1/6 Rack Width

    • EZ-SD1

      Storage Drawer - 1/6 Rack Width for EZ-RA6 or EZ-CC6

    • EZ-SD2

      Storage Drawer - 1/3 Rack Width for EZ-RA6 or EZ-CC6

    • EZ-SMB2

      Surface Mount Bezel for 1/3 Rack Width EZ Products

    • EZ-UCB2

      Under Counter Bracket Pair for all EZ Product Widths

      Dimensions

      EZ-MPA1

      Downloads

      DocumentsFormat
      ManualPDF
      CAD FilesUnitsFormat
      Engineering Functional BlockAmericanDXF
      Panel Diagram - FrontAmericanDXF
      Panel Diagram - FrontMetricDXF
      Panel Diagram - RearMetricDXF
      High Res ImagesFormat
      ez-mpa1.zipTIF
      Declaration of Conformity
      Download

      How To Buy

      Direct Dealer Program

      Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

      • Must be an A/V contractor, sound contractor or system integrator
      • Must possess a current resale certificate for your state
      Click here to submit a new direct dealer account inquiry

      Buy Online

      CompanyAddressPhoneLink
      Shopping cart close