RDL®

ST-LCR3

Logic Controlled Relay - Dual Alternate Pulse

SKU: ST-LCR3
  • Pulse at the Start of a Logic Signal
  • Pulse at the End of a Logic Signal
  • Relay Contact and Open-Collector Pulse
  • Active High or Active Low Inputs
  • Input Control Voltage From 3.3 to 24 Vdc
  • Control from Switch, Pushbutton, or Logic Circuits
  • Recommended Power Supply ( Not Included )
    PS-24AS (USA)PS-24AX (International)
    Category:

    Description

    The ST-LCR3 is ideally suited to applications where momentary pulses are needed from a single control signal. The module provides a momentary pulse when a logic signal at its input first becomes active. A separate momentary pulse is provided when the logic signal at the module input becomes inactive.

    Two logic inputs are available on the ST-LCR3. Either of these inputs may be used. Terminal 1 is internally pulled high to +5 Vdc. This input becomes active when an external closure or open-collector pulls the terminal to ground. The external switching device does not need to pull the terminal high, however the terminal may be pulled high with any voltage from +3.3 Vdc to +24 Vdc without any risk of damage to the ST-LCR3 input. Terminal 3 is internally pulled to ground. This input becomes active when an external closure or logic device applies a positive voltage from +3.3 Vdc to + 24 Vdc.

    When the input being used first becomes active the START PULSE output from the module is triggered. When the input first becomes inactive (after first being active) the END PULSE output from the module is triggered. Both the start and end pulses have a nominal duration of 250 ms.

    Each pulse output provides both an open-collector SLAVE terminal and relay contacts. The SLAVE terminal may be used to control other RDL modules and a variety of other equipment. The relay contacts may be used to control modules or equipment that do not operate from open-collector control.

    Specifications

    Inputs (2):Logic High or Logic Low (Low = ground, High = 3.3 Vdc to 24 Vdc)
    Outputs (2):Open collector @ 25 mA suitable to drive indicators or slave LCRs.
    Switching Contacts:Single Pole Relay Contacts (2)
    Maximum Switching Power:60 W (220 Vdc, 125 Vac, 2 A)
    Ambient Operating Environment0° C to 55° C
    Power Requirement:GROUND-REFERENCED, 24 Vdc @ 100 mA (assuming 20 mA max load at SLAVE output)
    Package Type:Cardboard Box
    Package Dimensions:2 x 2 x 4 in.
    Shipping Weight:0.2 lbs.
    WEEE weight:0.145 lbs.
    Tariff code:8543.70.9860

    Related Products

    Switching
    • ST-LCR1

      Logic Controlled Relay - Momentary

    • ST-LCR1H

      High Power Logic Controlled Relay - 8 A

    • ST-LCR2

      Logic Controlled Relay - Latching

    Related Products

    General Wiring Accessories
    • DTB

      STICK-ON® Series Detachable Terminal Block

    General Mounting Accessories
    • DMK-5

      Detachable Mounting Kit for RDL Modules

    • SR-4

      STICK-ON Series Mounting Rack - 7 modules

    • MB-1

      Mounting Kit - RU, ST and TX Series

    TX™ Mounting Accessories
    • MB-1

      Mounting Kit - RU, ST and TX Series

    DIN Rail Mounting Accessories
    • DRA-35S

      STICK-ON DIN Rail Adapter - 1 module

    • DRA-35S6

      STICK-ON DIN Rail Adapter - 6 modules

    STICK-ON® Mounting Accessories
    • STR-H6A

      10.4" Rack Mount for 6 STICK-ON Series Products

    • ST-PBR4

      STICK-ON Mounting Bracket

    • ST-RRB1

      Rear rack rail mounting kit for any STICK-ON module

    • SMK-12

      STICK-ON Mounting Plate

    • STR-19A

      STICK-ON Series 19" Racking System - 12 modules

    • SR-12A

      STICK-ON Series 19" Mounting Rack - 12 modules

    • STR-19B

      STICK-ON Series 19" Racking System - 10 modules

    • SR-10

      STICK-ON Series 19" Mounting Rack - 10 modules

    Dimensions

    ST-LCR3

    Downloads

    DocumentsFormat
    DatasheetPDF
    CAD FilesUnitsSizeFormat
    Engineering Functional BlockAmerican4.18 KBDXF
    Panel Diagram - EndAmerican4.25 KBDXF
    Panel Diagram - FrontAmerican31.46 KBDXF
    Panel Diagram - EndMetric3.96 KBDXF
    Panel Diagram - FrontMetric32.65 KBDXF
    High Res ImagesFormat
    st-lcr3.zipTIF
    Declaration of Conformity
    Download

    Diagrams

    Related Products

    • AMS-PB1

      Momentary SPDT Pushbutton - fits all AMS mounts

    • AMS-SW2

      Rocker Switch DPDT - fits all AMS mounts

    How To Buy

    Direct Dealer Program

    Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

    • Must be an A/V contractor, sound contractor or system integrator
    • Must possess a current resale certificate for your state
    Click here to submit a new direct dealer account inquiry

    Buy Online

    CompanyAddressPhoneLink
    Shopping cart close