RDL®

STM-DA3

Microphone Level Distribution Amplifier - 1x3

SKU: STM-DA3
  • Feed 1 Microphone to 3 Microphone Inputs
  • Electrical and Audio Isolation
  • Studio Quality Low-Noise, Low-Distortion Performance
  • Excellent Phase Response
  • Versatility of STICK-ON® Compactness
  • Recommended Power Supply ( Not Included )
    PS-24AS (USA)PS-24AX (International)
    Category:

    Description

    The STM-DA3 is designed for use in quality commercial sound, broadcast and recording applications. The 1.2 kΩ balanced input accepts a wide variety of microphone input levels without loading professional low impedance microphones. A multi-turn trimmer is user adjustable for either gain or loss in order to match the facility standard microphone levels. Three balanced outputs provide nearly total isolation between the output lines. Unlike mic-splitting transformer systems, the STM-DA3 also provides audio isolation. In fact, the audio isolation is so good that a +4 dBu signal fed into one output is still below the noise floor on the adjacent output. Loading of one output including a direct short, has no effect on the other outputs.

    The STM-DA3 is built on the electrical architecture of RDL's low-noise studio quality mic preamplifiers. Dynamic or condenser microphones may be used with the STM-DA3. Standard 24 V phantom is supplied to the input when the supply voltage is connected to the PHM terminal. Optimum operating level is set using RDL's unique Dual-LED VU meter, located adjacent to the terminal block. A green LED illuminates at 15 dB below optimum level. The intensity of the green LED progresses from minimum to full intensity over a 15 dB range. The adjacent red LED illuminates when the operating level exceeds the optimum level. This makes the STM-DA3 easy to set up without any external test equipment, and operating levels may be monitored at the module

    For Mic to Line level distribution, use the RDL STM-LDA3.

    Specifications

    Input:1.2 kΩ balanced
    Outputs (3): -45 dBu, 150 Ω balanced
    Gain Range:17 dB (Adjustable, 25-turn trimmer)
    Control Fully CCW:Gain = -5 dB
    Control Fully CW:Gain = 12 dB
    Frequency Response:30 Hz to 20 kHz (± 0.2 dB)
    THD+N:< 0.1%
    IMD:< 0.1%
    Noise: 20 dB (-50 dBu output, -45 dBu input)
    CMRR:> 60 dB (100 Hz to 5 kHz)
    Output Isolation:> 135 dB (balanced audio)
    > 150 dB (common mode)
    Ambient Operating Environment:0° C to 55° C
    Power Requirement:GROUND-REFERENCED, 24 Vdc @ 40 mA
    Package Type:Cardboard Box
    Package Dimensions:2 x 2 x 4 in.
    Shipping Weight:0.2 lbs.
    WEEE weight:0.145 lbs.
    Tariff code:8543.70.9860

    Related Products

    Distribution
    • RU-MLD4

      Microphone / Line Distribution Amplifier - 1x4

    Microphone Products
    • STM-2

      Adjustable Gain Microphone Preamplifier - 35 to 65 dB gain

    • STM-3

      High Gain Microphone Preamplifier - 45 to 75 dB gain

    • STM-LDA3

      Studio Quality Microphone Preamplifier with phantom - 3 line outputs

    Related Products

    STICK-ON® Mounting Accessories
    • STR-H6A

      10.4" Rack Mount for 6 STICK-ON Series Products

    • ST-PBR4

      STICK-ON Mounting Bracket

    • ST-RRB1

      Rear rack rail mounting kit for any STICK-ON module

    • SMK-12

      STICK-ON Mounting Plate

    • STR-19A

      STICK-ON Series 19" Racking System - 12 modules

    • SR-12A

      STICK-ON Series 19" Mounting Rack - 12 modules

    • STR-19B

      STICK-ON Series 19" Racking System - 10 modules

    • SR-10

      STICK-ON Series 19" Mounting Rack - 10 modules

    General Mounting Accessories
    • DMK-5

      Detachable Mounting Kit for RDL Modules

    • SR-4

      STICK-ON Series Mounting Rack - 7 modules

    • MB-1

      Mounting Kit - RU, ST and TX Series

    General Wiring Accessories
    • DTB

      STICK-ON® Series Detachable Terminal Block

    DIN Rail Mounting Accessories
    • DRA-35S

      STICK-ON DIN Rail Adapter - 1 module

    • DRA-35S6

      STICK-ON DIN Rail Adapter - 6 modules

    TX™ Mounting Accessories
    • MB-1

      Mounting Kit - RU, ST and TX Series

    Dimensions

    STM-DA3

    Downloads

    DocumentsFormat
    DatasheetPDF
    CAD FilesUnitsSizeFormat
    Engineering Functional BlockAmerican4.03 KBDXF
    Panel Diagram - EndAmerican3.85 KBDXF
    Panel Diagram - FrontAmerican67.91 KBDXF
    Panel Diagram - EndMetric3.86 KBDXF
    Panel Diagram - FrontMetric69.94 KBDXF
    High Res ImagesFormat
    stm-da3.zipTIF
    Declaration of Conformity
    Download

    Diagrams

    How To Buy

    Direct Dealer Program

    Becoming an RDL direct dealer is quick and easy. To become a direct dealer, your company must meet the following requirements:

    • Must be an A/V contractor, sound contractor or system integrator
    • Must possess a current resale certificate for your state
    Click here to submit a new direct dealer account inquiry

    Buy Online

    CompanyAddressPhoneLink
    Shopping cart close